We can Hack Chip Microchip PIC18F67K22 64/80-Pin 1-Mbit Enhanced Flash Microcontrollers chip, please view the IC mcu features for your reference:
Low-Power Features:
Special Microcontroller Features:
· Power-Managed modes:
– Run: CPU on, peripherals on
– Idle: CPU off, peripherals on
– Sleep: CPU off, peripherals off
· Two-Speed Oscillator Start-up
· Fail-Safe Clock Monitor
· Power-Saving Peripheral Module Disable (PMD)
· Ultra Low-Power Wake-up
· Fast Wake-up, 2 ms Typical
· Low-Power WDT, 300 nA Typical
· Ultra Low 50 nA Input Leakage
· Run mode Currents Down to Very Low 5.5 mA,
Typical
· Idle mode Currents Down to Very Low 2.2 mA,
Typical
· Sleep mode Currents Down to Very Low 20 nA,
Typical
· RTCC Current Downs to Very Low 700 nA,
Typical
Operating Voltage Range: 1.8V to 5.5V
On-Chip 3.3V Regulator
Operating Speed up to 64 MHz
Up to 128 Kbytes On-Chip Flash Program Memory
Data EEPROM of 1,024 Bytes 4K x 8 General Purpose Registers (SRAM) for IC breaking
10,000 Erase/Write Cycle Flash Program Memory, Typical
1,000,000 Erase/write Cycle Data EEPROM Memory, Typical
Flash Retention 40 Years, Minimum
Three Internal Oscillators: LF-INTRC (31 kHz),
MF-INTOSC (500 kHz) and HF-INTOSC (16 MHz)
Self-Programmable under Software Control
Priority Levels for Interrupts
8 x 8 Single-Cycle Hardware Multiplier
Extended Watchdog Timer (WDT):
– Programmable period from 4 ms to 4,194s (about 70 minutes)
In-Circuit Serial Programming™ (ICSP™) via
Two Pins
In-Circuit Debug via Two Pins
Programmable:
– BOR
– LVD
Peripheral Highlights:
· Up to Ten CCP/ECCP modules:
– Up to seven Capture/Compare/PWM (CCP) modules
– Three Enhanced Capture/Compare/PWM (ECCP) modules
· Up to Eleven 8/16-Bit Timer/Counter modules:
– Timer0 – 8/16-bit timer/counter with 8-bit programmable prescaler
– Timer1,3 – 16-bit timer/counter
– Timer2,4,6,8 – 8-bit timer/counter
– Timer5,7 – 16-bit timer/counter for 64k and 128k parts
– Timer10,12 – 8-bit timer/counter for 64k and 128k parts
· Three Analog Comparators from Hack Chip Microchip PIC18F67K22
· Configurable Reference Clock Output
· Hardware Real-Time Clock and Calendar (RTCC) module with Clock, Calendar and Alarm Functions
· Charge Time Measurement Unit (CTMU):
– Capacitance measurement for mTouch™ sensing solution
– Time measurement with 1 ns typical resolution
– Integrated temperature sensor
· High-Current Sink/Source 25 mA/25 mA (PORTB and PORTC)
· Up to Four External Interrupts
· Two Master Synchronous Serial Port (MSSP) modules:
– 3/4-wire SPI (supports all four SPI modes)
– I2C™ Master and Slave modes
· Two Enhanced Addressable USART modules:
– LIN/J2602 support
– Auto-Baud Detect (ABD)
· 12-Bit A/D Converter with up to 24 Channels:
– Auto-acquisition and Sleep operation
– Differential input mode of operation
· Integrated Voltage Reference
Operating Voltage Range: 1.8V to 5.5V
On-Chip 3.3V Regulator
Operating Speed up to 64 MHz
Up to 128 Kbytes On-Chip Flash Program Memory
Data EEPROM of 1,024 Bytes
4K x 8 General Purpose Registers (SRAM)
10,000 Erase/Write Cycle Flash Program
Memory, Typical
1,000,000 Erase/write Cycle Data EEPROM
Memory, Typical
Flash Retention 40 Years, Minimum
Three Internal Oscillators: LF-INTRC (31 kHz),
MF-INTOSC (500 kHz) and HF-INTOSC
(16 MHz)
Self-Programmable under Software Control
Priority Levels for Interrupts
8 x 8 Single-Cycle Hardware Multiplier
Extended Watchdog Timer (WDT):
– Programmable period from 4 ms to 4,194s (about 70 minutes)
In-Circuit Serial Programming™ (ICSP™) via
Two Pins
In-Circuit Debug via Two Pins
Programmable:
– BOR
– LVD