Crack IC PIC18F6393 Binary

Crack IC PIC18F6393 can help engineer to recover the firmware out from the original Microcontroller PIC18F6393, the standard formart will be in Binary or heximal;

Crack IC PIC18F6393 Binary

Crack IC PIC18F6393 Binary

LCD Driver Module Features:

· Direct Driving of LCD Panel

· Up to 192 Pixels: Software Selectable

· Programmable LCD Timing module:

– Multiple LCD timing sources available

– Up to four commons: Static, 1/2, 1/3 or 1/4 multiplex

– Static, 1/2 or 1/3 bias configuration

· Can Drive LCD Panel while in Sleep mode for Low-Power Operation

Run: CPU On, Peripherals On

Idle: CPU Off, Peripherals On

Sleep: CPU Off, Peripherals Off

Run mode Current Down to 14 ìA Typical

Idle mode Currents Down to 5.8 ìA Typical

Sleep mode Currents Down to 0.1 ìA Typical

Timer1 Oscillator: 1.8 ìA, 32 kHz, 2V

Watchdog Timer: 2.1 ìA Typical

Two-Speed Oscillator Start-up

Flexible Oscillator Structure:

· Four Crystal modes:

– LP: Up to 200 kHz

– XT: Up to 4 MHz

– HS: Up to 40 MHz

– HSPLL: 4-10 MHz (16-40 MHz internal)

· 4x Phase Lock Loop (available for crystal and internal oscillators)

· Two External RC modes, Up to 4 MHz

· Two External Clock modes, Up to 40 MHz

· Internal Oscillator Block:

– Eight selectable frequencies, from 31 kHz to 8 MHz

– Provides a complete range of clock speeds from 31 kHz to 32 MHz when used with PLL

– User-tunable to compensate for frequency drift

· Secondary Oscillator Using Timer1 at 32 kHz

· Fail-Safe Clock Monitor:

– Allows for safe shutdown of device if primary or secondary clock fails

Peripheral Highlights:

· 12-Bit, Up to 12-Channel Analog-to-Digital (A/D) Converter module:

– Auto-acquisition capability

– Conversion available during Sleep

· High-Current Sink/Source 25 mA/25 mA

· Four External Interrupts

· Four Input Change Interrupts

· Four 8-Bit/16-Bit Timer/Counter modules

· Real-Time Clock (RTC) Software module:

– Configurable 24-hour clock, calendar, automatic 100-year or 12,800-year, day-of-week calculator

– Uses Timer1

· Up to Two Capture/Compare/PWM (CCP) modules

· Master Synchronous Serial Port (MSSP) module

Supporting Three-Wire SPI (all four modes) and I2C™ Master and Slave modes

· Addressable USART module:

– Supports RS-485 and RS-232

· Enhanced Addressable USART module:

– Supports RS-485, RS-232 and LIN 1.2

– Auto-wake-up on Start bit

– Auto-Baud Detect

· Dual Analog Comparators with Input Multiplexing

Special Microcontroller Features:

· C Compiler Optimized Architecture:

– Optional extended instruction set designed to optimize re-entrant code

· 1000 Erase/Write Cycle Flash Program Memory Typical

· Flash Retention: 100 Years Typical

· Priority Levels for Interrupts

· 8 x 8 Single-Cycle Hardware Multiplier

· Extended Watchdog Timer (WDT):

– Programmable period from 4 ms to 132s

– 2% stability over VDD and temperature

· In-Circuit Serial Programming™ (ICSP™) via Two Pins

· In-Circuit Debug (ICD) via Two Pins

· Wide Operating Voltage Range: 2.0V to 5.5V


Tags: ,,,,,,,,,