IC Crack Service | MCU Crack Service | Microcontroller Unlock Service Provider

Read Microcontroller PIC18F2455 Flash content and eeprom data out from its memory and copy the firmware to other blank MCU PIC18F2455 through modify the circuitry pattern of the MCU to reset the status of MCU from locked to unlocked one;

· USB V2.0 Compliant

· Low Speed (1.5 Mb/s) and Full Speed (12 Mb/s)

· Supports Control, Interrupt, Isochronous and Bulk Transfers

· Supports up to 32 Endpoints (16 bidirectional)

· 1-Kbyte Dual Access RAM for USB

· On-Chip USB Transceiver with On-Chip Voltage Regulator

· Interface for Off-Chip USB Transceiver

· Streaming Parallel Port (SPP) for USB streaming transfers (40/44-pin devices only)

Run: CPU on, peripherals on

Idle: CPU off, peripherals on

Sleep: CPU off, peripherals off

Idle mode currents down to 5.8 ìA typical

Sleep mode currents down to 0.1 ìA typical

Timer1 Oscillator: 1.1 ìA typical, 32 kHz, 2V

Watchdog Timer: 2.1 ìA typical

Flexible Oscillator Structure:

· Four Crystal modes, including High Precision PLL for USB

· Two External Clock modes, up to 48 MHz

· Internal Oscillator Block:

– 8 user-selectable frequencies, from 31 kHz to 8 MHz

– User-tunable to compensate for frequency drift

· Secondary Oscillator using Timer1 @ 32 kHz

· Dual Oscillator options allow microcontroller and USB module to run at different clock speeds

· Fail-Safe Clock Monitor:

– Allows for safe shutdown if any clock stops

Peripheral Highlights:

High-Current Sink/Source: 25 mA/25 mA

Three External Interrupts

Four Timer modules (Timer0 to Timer3)

Up to 2 Capture/Compare/PWM (CCP) modules:

– Capture is 16-bit, max. resolution 5.2 ns (TCY/16)

– Compare is 16-bit, max. resolution 83.3 ns (TCY)

– PWM output: PWM resolution is 1 to 10-bit

Enhanced Capture/Compare/PWM (ECCP) module:

– Multiple output modes

– Selectable polarity

– Programmable dead time

– Auto-shutdown and auto-restart in order to extract IC code

Enhanced USART module:

Master Synchronous Serial Port (MSSP) module

supporting 3-wire SPI (all 4 modes) and I2C™ Master and Slave modes 10-bit, up to 13-channel Analog-to-Digital Converter module (A/D) with Programmable Acquisition Time Dual Analog Comparators with Input Multiplexing

· C Compiler Optimized Architecture with optional Extended Instruction Set

· 100,000 Erase/Write Cycle Enhanced Flash Program Memory typical

· 1,000,000 Erase/Write Cycle Data EEPROM Memory typical

· Flash/Data EEPROM Retention: > 40 years

· Self-Programmable under Software Control

· Priority Levels for Interrupts

· 8 x 8 Single-Cycle Hardware Multiplier

· Extended Watchdog Timer (WDT):

– Programmable period from 41 ms to 131s

· Programmable Code Protection

· Single-Supply 5V In-Circuit Serial Programming™ (ICSP™) via two pins

· In-Circuit Debug (ICD) via two pins

· Optional dedicated ICD/ICSP port (44-pin devices only)

· Wide Operating Voltage Range (2.0V to 5.5V)

 

Tags: read microcontroller flash archive,read microcontroller flash code,read microcontroller flash content,read microcontroller flash data,read microcontroller flash eeprom,read microcontroller flash file,read microcontroller flash firmware,read microcontroller flash information,read microcontroller flash memory,read microcontroller flash program